A Simple Door Alarm Using a Clothes Peg


This is a short YouTube video from DrScrew channel that shows you how you can make a simple door alarm with items lying around your house. Below is the video from their YouTube channel and if you have a slow connection, I have screenshot some of the important steps on how to make the alarm.

How to make a simple door alarm by DrScrew


Video Screenshots


First, you will need a spare clothes peg like this one above.


Then, you will need a glue gun.


Using the glue gun, glue 2 AA batteries onto the peg, one on both side just like what is shown above.


Drill a hole through the tip of the peg.


Fix a small screw into the hole.


Prepare your buzzer for soldering. You can use any buzzer you can find from your old mother board or old electronics appliances that have one.


Glue the buzzer to the peg.


Solder the buzzer wires to the tip and to the battery terminal.


Solder a wire to connect the 2 batteries terminal. Please note the polarity of the battery.


Solder the other tip with a wire and connect to the other battery.


Now make a contact blocking sheet like this.


Slide it in between the peg tip. If you pull it out, the buzzer will sound.


This is a simple demonstration how you can apply on a door. If anyone were to open the door, the alarm will get triggered and buzzzzz!



Comments

Post a Comment

Popular posts from this blog

City Code Table for Casio SGW300HD-1AV Watch

Image
This city codes are provided in the watch user manual but for the ease of references in the web, I put this table in this blog in case i wanted to refer to it using my smartphone. Hope you find this useful. Code City UTC/GMT offset (hours) WLG Wellington 12 NOU Noumea 11 GUM Guam 10 SYD Sydney 10 ADL Adelaide 9.5 SEL Seoul 9 TYO Tokyo 9 KUL Kuala Lumpur 8 HKG Hong Kong 8 SIN Singapore 8 BJS Beijing 8 PER Perth 8 TPE Taipei 8 BKK Bangkok 7 RGN Yangon 6.5 DAC Dhaka 6 KTM Kathmandu 5.75 DEL Delhi 5.5 KHI Karachi 5 KBL Kabul 4.5 DXB Dubai 4 THR Tehran 3.5 JED Jeddah 3 DOH Doha, Qatar 3 MOW Moscow 3 BGW Baghdad 3 HEL Helsinki 2 ATH Athens 2 ANK Ankara 2
Read more

How to force only 4G or LTE network connection for Samsung Galaxy Note 4

Image
This is how to enable Samsung Galaxy Note 4 to force use only 4G (LTE) network connection for high speed internet data. There is a built-in switch in the smartphone that will enable the smartphone to force use only either 3G (WCDMA) or 2G (GSM) network connection but, there is no switch at all to enable the smartphone to force use only 4G (LTE) network connection. Video Tutorial This is screen video record to show you how to do it. If you prefer screenshots, please skip this video and scroll after the video. Screenshots Tutorial If you are clueless about the existing settings that enable you to switch network mode, goto “Settings > More networks > Mobile networks > Network mode”. Steps: Step 1 : From the phone dialer, dial *#2263# and the smartphone will bring you into the “Service Mode” screen like below. Step 2 : Select “[4] LTE BAND PART1 []” and the smartphone will bring you into a screen to select the types of LTE mode. Step 3 : Select “[1] LTE ALL []” to force the smartp
Read more

Mounting NFS share directory from D-link DNS 320L on Ubuntu 12.04 LTS

Image
Seems like the steps on how to get the NFS mount point from the D-Link DNS 320L NAS server were not properly documented in their user manual. After setting up and enabled the NFS service on the D-Link DNS 320L NAS server, I went ahead to setup and mount the share directory/folder in Ubuntu 12.04 LTS assuming the mount point in NAS was /Volume_1/... but that is not the correct mount point to start with! Found this answer from D-Link forum post from a member (ba43123) that helped me to correctly mount the NFS share directory/folder on Ubuntu 12.04 LTS: After spending most of the last hour on the phone with D-Link Technical Support, I came away with the recommendation to take my Mac (which has successfully connected to a number of NFS shares in the past) to Apple to determine if the network settings for NFS are correct.  This is mostly due to the fact that the people who are taking the calls have no information about NFS in their scripts and Knowledge Base so they are at a total loss in
Read more